Reasons Your Fiat 500 Key Fob Won’t Work
A key fob with the fiat van key replacement 500 number is a great way to unlock the doors and get started the car. There are a variety of reasons why the fob could stop working. This could be due to a dead battery, water damage, problems with receiver modules, as well as interference.
This listing is for a NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It needs to be professionally programmed (click here where to get a fiat key cut search for local locksmiths for your vehicle). Includes lock, unlock and trunk buttons.
Dead Coin Battery
The most frequent reason that your 500 key fob won’t function is a dead battery. Key fobs of today have limited operating range and must be within just a few inches of the vehicle to work. If you are far from your vehicle and hit the keyfob, it won’t respond and display the message “Key Fob Not Detected”.
If this occurs, replace the coin-cell battery (Part Number CR2032) by a fresh one of a trusted brand such as Panasonic Duracell or Energizer. They can be found in the local hardware store or online.
You can test the battery on your coin-cell by pressing the buttons while you’re standing close to your Fiat 500. The parking lights will flash and the key fob will operate the lock and unlock switches.
If your key fob isn’t working even after replacing the battery, it could be water damage that is preventing it from connecting to the module in your vehicle. Water damage can happen through a variety of methods, including a simple splash or submerging your key fob in saltwater at the beach. If you suspect your fob was exposed to water, try placing it in a dry rice bag to pull the moisture back out. If that doesn’t work your fob will probably require reprogramming by an experienced auto locksmith or by the dealer.
Water Damage
Damage to the water supply can occur if you immerse the fob into the ocean or wash it in a washer. Saltwater can cause the circuit board to short and then end up dying. It’s not a good thing to soak the fob in water however, don’t give it up in the event that you accidentally drop it in water or fail to remove it from your pants pocket.
First take the battery off the fob. Clean the electronic chip with isopropyl alcohol or a similar product and dry it completely before replacing the battery. Next check the fob to see if it works. If the key isn’t working then it might need to be reset. This is usually done by an auto locksmith or dealer.
If the key is a newer model and has not been programmed to your vehicle, it will likely need to be replaced completely. This is a straightforward process which can be accomplished by a professional automotive locksmith. The locksmith will need to cut the key to match the ignition in your vehicle. They will also need to reprogram the fob in your car’s system. This is a cheap and quick process that could be completed in the same day.
Receiver Module Issues
The 500 key fob you have may not work because it’s out of range. The remote’s range is of 30 feet. So if you are too far from your car it won’t respond to your commands. It’s easy to solve this problem by moving the remote closer to your vehicle until it responds.
If you’ve replaced the battery on your coin (commonly called”button” or “button” or “watch”) and your fob still won’t work it could be due to an internal circuit board problem. Reprogramming the fob typically resolves this issue. You can find the instructions for the majority of vehicles on YouTube or in the owner’s guide.
It may be necessary to replace the clips made of metal that hold the coin batteries in their place. If they lose tension, it could hinder the battery from being seated properly and can cause the remote to malfunction.
In rare instances the fob might become disconnected from your vehicle because of software or hardware issues. This could be a huge headache, but you can usually fix it by visiting an auto locksmith to reprogram your fob. In some cases the software may require reinstallation in your body control modules.
Interference
Interference can also cause the key fob to not be able to receive or transmit an signal. This can happen when the key fob is in proximity to a radio transmitter (cell phones and radar detectors) or any other source of electromagnetic radiation. The key fob might not function because of a problem with the buttons or water damage, or damage to the internal chips.
If your key fob suddenly stopped working, or if you have tried everything at home to fix it (e.g. You may have a faulty 500 receiver module if you’ve tried replacing the battery, reprogramming, or using a Spare fiat 500 key replacement uk 500 Key, Yjglobal.Net, key fob. The receiver module, which is located under the dashboard, picks up radio frequency signals from your key fob. It then converts them into electronic commands that the vehicle interprets.
There is a simple way to reset the 500’s on-board system including the keyfob. Disconnect the battery of 12 volts for about 15 minutes by taking off the negative cable first then the positive cable. Reconnect the battery. This will remove any remaining electrical charge, and then restart the car’s computer. This will help you get your key fob working again. If the issue persists, you should consult an expert certified technician. They will be able to identify the exact cause of issues.