Reasons Why Your nissan micra key replacement Qashqai Key Fob Won’t Work
The Qashqai has a distinct SUV-like appearance due to its bigger dimensions, and the ride on 19-inch wheels in Ti and ST-L models can be a bit firm at times. The front tyres of the Qashqai are also prone to losing traction on rough surfaces, and the CVT may occasionally show wrist-flexing torque steering.
It is usually caused by a dead coin battery which is easily replaced in just a few minutes. Be sure that the replacement battery is the same voltage, size and specifications.
Water Damage
One of the most frequent reasons a Nissan key fob will give the “key ID is not correct” message is due to water damage. The key fob comes with rubber seals that protect the chip inside. However, prolonged exposure to moisture can cause it to cease functioning properly. This is often the case when you drop your key fob into the ocean or a pool pools, but it could also happen if it gets wet due to soapy hands or rain.
If your key fob was exposed to water for an extended period of time it is possible to clean it using isopropyl and electronic cleaner. It might also need to be sent to a specialist for repair or replacement.
If your key fob is in need to be replaced, it is an easy procedure. First, ensure you have an appropriate multipack battery (CR2032 3V). Then, open the front and back cases with the help of a small screwdriver. You’ll need to take out the clips for retaining metal and then push out the old battery and replace it with the new one. After reassembling the fob, put the mechanical key back into place and check that it functions as intended. If not then you’ll have to bring it to a local Nissan dealer or a professional locksmith to replace the chip that controls the key. The chip is usually not damaged by water so it should not be too expensive.
Dead Coin Battery
Another common reason your Nissan Qashqai key fob may not work is because the battery for the coin is dead. They last for 3 to 5 years, but they are prone to failure over time in the event that the fob has been dropped frequently. You can try replacing the battery with a fresh one, but make sure that it’s the same size and voltage as the original. If you choose to use a different battery, it can cause the key to have an incorrect key ID which can prevent it from pairing with your vehicle.
The most efficient method of replacing the battery on a nissan replacement key Qashqai key fob is by prying open the fob with an small screwdriver that has a flat head. The screwdriver needs to be inserted into a small hole on the bottom of the key fob. Make sure to gently twist the screwdriver to split the two halves. Then, remove the old CR2025 button cell battery and insert the new one after confirming its position in the fob.
Check the terminals for any dirt or water damage prior to installing the new battery. If this is the case clean the terminals using some isopropyl ethanol. Also, make sure the pole cables are plugged in correctly. They should be connected to the positive and negative poles of the battery, respectively.
Troubleshooting
If your Nissan Qashqai’s main fob stops working after being exposed to clean tap or rain water, this could be a sign that there’s an issue with the internal chip. You’ll need a new keyfob if you are unable to fix the issue by changing the battery. If the key fob has stopped working after dropping it, it’s likely that the chip inside was damaged. If you clean the chip with isopropylethanol and paper towels and then insert it into the key fob, you’ll generally get it working.
A common error that you may notice on your car’s dashboard is “Key ID Not Correct.” This means that the car cannot recognize the key fob, and will not allow it to start the engine. The issue can be caused by several things such as water damage, undetectable problems in the circuitry of the key fob or RFID interference.
The key fob will stop working if the 12 volt batteries are dead or don’t provide enough electrical current. This will affect the remote keyless system and central locking on your Nissan Qashqai, as well as stopping you from starting your engine using the key fob (if equipped with Intelligent Key). Check the batteries in the key fob if you are not able to lock and unlock your door by hand. You may also try reinserting the battery to reset the transmitter.
Reprogramming
If the key fob had not been submerged in salt water the device should be able to come back to life after a quick rinse with clean water. You can also clean the electronic chip with isopropyl or electronic cleaner. If none of these work it is possible to replace the key fob.
If your nissan car key replacement price Intelligent Key is still not working, it could be an issue with the connection between it and your car. Start by turning the ignition key without activating the vehicle. Repeat this process until the hazard light blinks twice. Then, turn the vehicle off and take away the keys.
Next, then open the fob compartment in your vehicle. This is usually located in a door jamb on the driver’s side door handle or underneath an armrest. Find the small “program” button and press it. You should hear a chime once the process is complete.
Now that your Intelligent Key is relinked to the car, it’s time to test it out. Set your feet a distance from the car, and hit all the buttons on the key. If the lights flash and the horn sounds it means the key has been successfully linked to the nissan elgrand key Fob Programming. You can also test it close to the nissan key fobs.