How to Change a subaru legacy replacement key cost Spare Key
If you’ve lost your Subaru car key, you should call a locksmith. Usually, they can cut an alternative key for you cheaper than the dealer.
Subaru car keys are typically either intelligent “push-to-start” fob remote keys or basic keys made of metal. The Fob key will need to have its chip changed.
Keyless Entry System
The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your car or the lift gate. The remotes use keys inside your car to connect to the computer system of your vehicle.
Some models of Subaru offer a little-known feature called PIN Code Access. This allows you to utilize a personal sequence of numbers to open and start your vehicle. Check your owner’s guide to learn how to utilize this feature if you have a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.
If your keys stop functioning, there’s a good possibility that the battery inside the key fob is dying. You can check the battery life of your key fob using a portable tester or a multimeter you can find in your garage.
Next, you’ll want to take the key fob out of its case and inspect the circuit board of its transmitter. You will see one or two sets of eight-digit numbers. Note down the first set so you can remember it. After you’ve done this you can begin programming your key fob at home. The process for doing this is different based on the model and year of your vehicle, but it’s usually simple enough to do yourself.
Key Fobs
Subaru’s latest models come with key fobs that not only unlock doors however, they also turn on your lights, lock your gas cap, and even start your vehicle. That last trick is especially helpful if you’ve ever arrived at the gas station only to find that your car isn’t starting because the battery of the key fob failed.
No matter if your reprogram subaru key is brand new or old, it’s likely that the key fob can be replaced with no difficulty. It’s important to remember that newer models with the highest level of technological advancement may require an appointment at the dealership. But, with a bit of time and effort, you can find a replacement key fob to use at home.
Begin by looking at the circuit board for the transmitter inside your key fob (instructions to open the case are provided in the owner’s guide). There should be two or more serial numbers with 8 numbers each. Write down the first number series and save it for reference in the future.
Next, climb into your driver’s seat and shut all doors. Turn the key 10 times to start your car, then turn off. Press the lock button of your key fob, and then open the door. This will test that your doors are functioning correctly. After that close the door, and remove the key from the ignition. You should hear the chime from your vehicle, signaling that the key fob is programmed.
Ignition System
If your reprogram subaru key keys aren’t functioning as they should it could be because the key battery is dead. You can replace the battery in your key fob at home if you are familiar with the procedure. The replacement of the battery is affordable and easy to find. If the key fob you have doesn’t respond to your commands, it could be a different issue. It’s recommended that you go to a dealer to obtain an extra key. They will ensure that the key is genuine Subaru key, under warranty, and will be programmed for your vehicle. This is far safer and simpler than buying an aftermarket key from a business on the internet.
The dealer can also cut a key for you if you give them your VIN number and as proof of ownership. They’ll use this information to program the new key in order to be accepted by the immobilizer. This is a more complex procedure than cutting a single key, and the dealership will charge more for it.
After the new key has been programmed, you’ll be able to swap it out with your current key. It takes only five seconds to insert the new key, so be sure to keep your working key close at hand. You can remove the key when the security light has been off and you’ve tested it.
Battery Replacement
Subaru fobs are extremely beneficial because they can switch on the sunroof and power windows of your vehicle with a single button press. The battery in your Subaru fob wasn’t made to last forever, and it will need to be changed eventually. Fortunately, replacing subaru key the battery is a simple procedure that you can carry out yourself with the assistance of this brief guide from Capitol subaru Key car.
You’ll need to locate the small gap that separates the front and back of your keyfob. You can open this seam using a flathead screwdriver to reveal the small compartment that houses the battery. Remove the old battery and then put in a new one, making sure that it is facing the correct side up. Once you’ve assembled everything you can use the new key fob for locking, unlocking, and starting your vehicle.
You should always have a spare set of keys, particularly if yours is broken or has been lost. You can purchase a brand new key at your local dealership or get it cut by a locksmith. Whatever you choose, it’s essential to get your key fob operating properly quickly so that you can drive safely!