Replacing uPVC Window Handles
The replacement of window handles made of upvc is an easy task. The important thing is to ensure that the new handle is a good fit for the spindle cut out in the window locking handles mechanism.
If the steps below are followed correctly the cockspur handle will be able to fit into most windows. The height of the step of the handle is crucial.
What to Look for
A lot of windows in the UK are fitted with uPVC handles Over time, they will begin to show signs of wear and tear. The handle on the window may become shaky or difficult to operate when this occurs. Anyone who is comfortable with basic hand tools can complete this relatively simple job.
The first step is to make sure that the handle is firmly fixed to the window frame and is in the open position. The next step is to find the fixing pins or screws that hold the handle in place. These are typically located on the inside of the handle and can be removed with a screwdriver, or pliers.
When the handle is loose, gently pull it away from its hinges. The next step is to find a replacement handle of the same style and size. This can be accomplished online or at a local DIY store, and the process should only take five minutes using an screwdriver.
The most important thing to consider when replacing the uPVC window handle is the step height. This is the distance between the handle’s base and where it is placed within the frame of the window. It is generally an average measurement, but it is important to check the step height of your current handle prior to ordering the new one.
Depending on the type of handle you have There are various sizes that are available. Inline handles for upvc windows (read this blog article from Bravejournal) usually have lug centres of 31mm as well as varieties of cockspur handles that have 43mm centres. Tilt and turn handles are typically found on uPVC windows, and they come with a unique design that allows the window to be tilted in to allow for ventilation, and then turned to open the window completely.
The most common uPVC handle breakage is internal cracking rather than a fracture from the base. This can make it difficult to open. It is crucial to make sure that any replacement handle is fitted with the same spindle that was used in your original one.
Remove the Old Handle
Incorrectly installed or damaged window handles may cause your double glazed windows to close or open improperly and could even cause them to become stuck. There are many reasons like general wear and tear or the corrosion of the handle made of metal. In these cases it is essential to seek replacement handles made of upvc as soon as you can to avoid further damage and loss of function.
When replacing upvc windows handles it is recommended to remove the old handles from the window. To do this, start by removing the screw that is covered when the handle is in the closed position. This will reveal a screw and once removed, you can begin to take off the handle itself. You can make the job easier by using an electronic screwdriver.
It is also important to note that the screws on the handle may be hidden behind plastic caps, so it is recommended to take a Stanley knife to the screw caps and then remove them. After removing the handle, you’ll be required to inspect the square cutout on the base to ensure that the new handle you choose for the window sash lock door handles is compatible. It is essential to measure the length of the spindle on the old handle and compare it to the dimensions of the window mechanism spindle cutout.
There are three types of Upvc handles: Espag handles with a central screw that can be turned right or left and Cranked handles with two screws and Spade handles that have flat arms and can be used on either side of the windows made of upvc. It is easy to replace the handle once you have located one that is suitable. Simply screw it into place, and ensure that the spindle is properly inserted into the lock mechanism. After that, it should be tightened to the window frame and the replacement upvc window handles should be secure.
Measure the Spindle
If you’re replacing a upvc window handle that has come off, it’s because the spindle holding it in place has become damaged or loose. In some cases, you can tighten the spindle with pin or screw. In some cases, it may be necessary to replace the handle. There are several different types of handles made of upvc. There are three kinds of handles: inline espagnolette cockspur, and tilt-and-turn. Each handle type is installed and replaced in a different manner.
Before you purchase a new handle, it’s important to know the dimensions of the one you have. This will ensure that the handle will fit the window properly and will be of the correct size. Fortunately, all handles follow industry standard sizing so it’s quite easy to locate the correct size.
To measure the size of your handle first remove it from the window by turning it to an open position. You should be able see the size of the screw or pin that holds the handle. Then, use a tape measure or ruler to determine the length of the spindle. Once you know the length of the spindle you can buy a new one with the same length.
When you are looking to replace a handle, it is important to consider the step height of an window handle made of upvc. The step height is measured from the base to the point where the handle sits on the frame. Typically, this will be around 21mm for uPVC windows, and 9mm for aluminium. Dropping something in the gap will let you observe how far the handle extends before it reaches an obstruction.
Cockspur handles often have different backset heights depending on the type of window they’re installed in. Inline Espag handles come with a standard height of 43mm from centre to centre (2 fixing points). Cockspur handles however have different backset heights according to the style of the window they are in. This is because they have a spur that extends from their handle and locks onto a cockspur wedge-striking plate.
Install the New Handle
Once you’ve selected the new handle, align it carefully with the holes for screws on the door. Then secure it using the screws provided. If you’re also replacing the latch lever the lever can be mounted in a similar way to the conservatory door handles handle. Then, attach the door trim to conceal the screws for mounting.
Tip: To remove the head made of metal from the wooden wedge, hold the handle so its longer end is resting on the floor. Use a hammer to tap on the thin end of the handle. Be careful not to scratch the handle or spindle.