Reasons Your fiat key cutting 500 Key Fob Won’t Work
A key fob from Fiat 500 is a handy way to unlock the doors and start the car. There are a myriad of reasons the fob could stop working. These include a dead coin battery water damage, receiver module issues, and interference.
This listing is for an NEW replacement fiat key cutting Flip Key Remote that looks like the Ilco brand. It must be professionally programmed (click here to find local locksmiths for your vehicle). It comes with lock, unlock and trunk buttons.
Dead Coin Battery
A dead battery is probably the most common reason for your 500 key fob not working. Modern key fobs have a very limited range of operation, and should be within a few feet of the vehicle in order to function. If you are further away from your vehicle, and you press the keyfob button it will not respond, and display the message “Key Fob Not Detected”.
If this occurs, replace the coin-cell battery (Part Number CR2032) by a brand new one of a reputable brand such as Panasonic Duracell or Energizer. They are usually available at your local hardware store or online.
You can test the battery on your coin-cell by pressing the buttons while you are standing close to your fiat doblo key fob programming 500. The car should flash its parking lights, and the key fob should be able to operate the lock and unlock buttons.
If your key fob still doesn’t work even after replacing the battery, it may be water damage which has prevented it from communicating with the module inside your vehicle. Water damage can occur through a variety of methods, including a simple splash or submerging the key fob into saltwater at the beach. If you suspect that your fob has been exposed to water, put it in a dry rice bag to pull the moisture out. If this does not work, you’ll need to have the fob reset by an auto locksmith or a dealer.
Water Damage
Although the fob is equipped with rubber seals to keep water from the electronic chip inside, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short, and eventually cease to function. If you get the fob wet, it’s not an ideal idea however, if you drop it into a glass of water or do not remember to remove it from your pocket before you run the washer do not give up hope.
Remove the battery first. Clean the electronic chip using isopropyl alcohol or a similar product and dry it completely before replacing the battery. Test the fob afterward to determine if it’s working. If the key doesn’t function, it may need to be reset. This is usually handled by an auto locksmith or dealer.
If your key is old and has not been programmed to work with your vehicle, you will need to replace it completely. A professional locksmith for automotive will be able to complete this process. The locksmith must cut the key to match the ignition of your vehicle. The locksmith also needs to reprogram your fob in the vehicle’s system. This is an affordable and quick process that could be completed the same day.
Receiver Module Issues
One of the simplest reasons your 500 key fob won’t be functioning is because it’s out of range. The remote typically has an operating range of 30 feet or less and if it’s far away from your lost car keys fiat 500 key programming (https://rindom-capps.Mdwrite.net) it will not respond to your commands. It is possible to remedy this by moving your remote closer to your vehicle until it responds.
If you’ve replaced the battery in your coin (commonly known as a “button” or “watch”) and your fob doesn’t function it could be due to an internal circuit board problem. Reprogramming the fob is usually the solution to the issue. You can find the instructions on how to do this on the majority of vehicles by searching YouTube or looking through the owner’s manual.
You may need to replace the metal clips that hold the coin battery. If they lose tension it can prevent your coin battery from being properly seated and cause your remote to malfunction.
In rare cases the fob could be out of connection with your vehicle as a result of software or hardware problems. You can fix this problem by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances they may have to reinstall the software in your body control module, too.
Interference
Interference can also cause the key fob to be unable to receive or transmit a signal. This can occur when the keyfob is located in close proximity to a radio transmitter such as a cell phone or radar detector. The key fob may not work because of a weak connection with the buttons water damage or damage to the internal chips.
If your key fob suddenly stopped working, or you have tried everything at home to solve the issue (e.g. You may have a faulty 500 receiver module in the event that you’ve tried replacing the battery, reprogramming or using a spare key fob. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. It converts the signals into electronic commands that are then interpreted by the vehicle.
Fortunately, there’s an easy way to reset all on-board systems in your 500 device, including the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Reconnect the battery. This will remove any remaining electricity and restart the car’s computers, which could allow you to the key fob to function again. If the problem persists, you should consult an experienced technician. They will be able to identify the exact cause of issues.