Fiat 500 Replacement Key Fob
If your remote key fob isn’t working, it might be time to replace the battery. If you replace the battery and it’s still not working it could be a problem somewhere else.
At United Locksmith, we specialize in the creation of new keys for old cars. We have all the tools and parts necessary to perform this service.
Dead Coin Battery
A dead battery is the most frequent cause of your fiat punto replacement key 500 replacement key cost (kmbfamily.Net) 500 keyfob not locking or unlocking the doors. The key fob comes with a coin cell battery that will drain quickly in the event that it is not used often enough. If your remote began to show signs of weakening such as a loss of range and then completely stopped working, the battery is probably dead.
Metal clips hold the battery in on the key fob. If the clips aren’t tight, they can cause contact issues that prevent your remote from receiving power. Use a flathead screwdriver break open the retaining clip and then remove the old battery. Choose a battery that is the same voltage, size and specifications as the original.
The key fob could also become corroded or damaged by exposure to water. Even a small bath in soapy, warm water could cause damage to the chip. Make sure your key fob is dry.
Water Damage
Water damage could be the reason for your key fob’s inability to function properly. Key fobs have rubber seals that stop them from being damaged by a light rain or a splash of water. However, it is very important to keep your car locked keys in car boot fiat punto from being tossed into the pool, ocean and washing machine!
The key fob has an electronic chip which sends an electronic message to the immobilizer system in your car. This is what allows your 500 to start or lock, however should the chip become wet, it will no longer function.
You can try cleaning your key fob’s internal electronics with isopropyl Alcohol or an electronic cleaner to see if they are still good. However, it is probably better to purchase a new one from a dealer instead of trying to repair the key fob which is submerged in salt water.
A replacement fob could cost you a bit however, it’s cheaper than having to have your Fiat 500 towed to a dealership and fixed there! You could also do it yourself by following some simple steps. Be sure to have the correct type of battery before you attempt to open your keyfob. You can find step-bystep instructions for every car keyfob online.
Faulty Chip
The chip located within the key fob communicates with your car’s immobiliser unit to ensure the car is capable of starting when the correct key is used. If the chip is damaged or damaged in any way it will not start.
Damage to the water or a dead phone battery are the most common reasons for an unreliable chip. Regardless of the reason, it is recommended to delegate the job to a locksmith since they can replace the chip for you quickly and at a low cost.
If your key fob will not work after exposure to clean water from a tap or rain then remove the battery. Wipe down the electronic component with paper towels. If the key fob does not function, there’s a chance that it has an issue with the component and requires to be replaced.
A few people turn to their dealer when in need of a new Fiat key fob, but it can be a costly option. United Locksmith is the best option if you would like to have your Fiat keyfob repaired at a reasonable cost. We have the equipment and know-how required to repair your fiat 500 replacement key uk key fob in a timely and professional manner.
Faulty Receiver Module
fiat panda key programming key fobs transmit signals up 50 feet to the vehicle, which allows it to unlock and close the doors (and start the vehicle for those with automatic transmissions). There are several reasons why the fob could not function. This could be due to a dead coin battery, water damage, worn buttons and a receiver module issue, and signal interference or an electronic chip that is malfunctioning.
If the fob was in a pocket which has endured extreme trauma, like falling on hard floor or being washed in a washer, it may not be capable of communicating with the car’s Body Control Module (BCM). This is because the BCM is an extremely secure system that will only accept a signal from a genuine key and not another.
If this is the case, then you have to replace your fob. A professional locksmith will manage the entire replacement process including programming a new key to your 500. In fact, they can even offer you a clone key that functions exactly the same way as the original fob (and costs a fraction of the cost).