Reasons Your fiat tipo key 500 Key Fob Won’t Work
A fiat 500 replacement key fob 500 key fob is a convenient method to unlock the doors and start the car. There are many reasons why the fob may stop working. These include a dead battery or water damage, receiver module issues, and interfering.
This listing is for a NEW replacement fiat panda Key Flip Key Remote that looks like the Ilco brand. It must be professionally programmed (click here to find local locksmiths for automotive locksmiths). It includes trunk, lock and unlock buttons.
Dead Coin Battery
A dead battery is the most common cause of your 500 key fob being inoperative. Key fobs of today have only a limited range of operation and must be within only a few inches from the vehicle in order to function. If you’re far away from your vehicle when you press the key fob button the car will not respond, and will display a “Key Fob Not Detected” message in the instrument cluster.
If this happens If this happens, replace the battery in the coin-cell (Part Number CR2032) with a new battery of a trusted brand like Panasonic Duracell or Energizer. They are available at your local hardware store, or on the internet.
You can test the coin-cell battery by pressing the buttons while standing close to your fiat 500 spare key cost 500. The parking lights will flash and the key fob should operate the lock and unlock switches.
If your key fob does not work after replacing the battery, it might be water damage that hinders it from connecting to the module in your vehicle. Water damage can happen in a number of ways, from a light splash to submerging the fob in salt water at the beach. If you suspect your fob was exposed to water, try placing it in a dry rice bag to pull the moisture out. If that doesn’t work, your fob will probably need to be reset by a professional auto locksmith or dealer.
Water Damage
Although the fob is equipped with rubber seals that keep water out of the chip’s electronic circuit the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short, and eventually fail. It’s not a good idea to let the fob get wet, but don’t give it up even if you accidentally drop the fob in the water or don’t remove it from your pants pocket.
First take the battery off the fob. Clean the electronic chip with isopropyl alcohol or a similar product and dry it thoroughly before replacing the battery. Test the fob afterward to see if it is working. If the key does not function, it may have to be changed. This is usually done by a professional or dealer auto locksmith.
If your key is old and has not been programmed to work with your vehicle You will need to replace it completely. This is a simple procedure that can be carried out by a professional automotive locksmith. The locksmith will require the key cut to match your car’s ignition. They will also need to reprogram the fob in your vehicle’s system. This is a quick and inexpensive process that can be completed within the next day.
Receiver Module Issues
One of the simplest reasons why your 500 key fob won’t be working is that it’s simply out of range. The remote has a range of 30 feet. So if you are too far from your car it will not respond to your commands. This can be fixed by moving it closer to your vehicle until it begins responding.
If your fob does not work after replacing the coin battery, also known as a “button”, “watch” or “button” It could be due to an issue with the circuit board inside. Reprogramming the fob usually resolves the issue. There are instructions on how to do this for the majority of vehicles by searching YouTube or checking out the owner’s manual.
It is sometimes necessary to replace the metal clips that hold the coin batteries in place. If they loose tension, it can prevent the battery from being properly seated and result in the malfunction of your remote.
In rare instances, the fob might be out of sync with your vehicle because of hardware or software issues. This can be a major problem, but you can often fix this by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In some cases they may have to install the software again in your body control module, too.
Interference
Interference can also cause the key fob to be unable to receive or transmit signals. This could occur if the key fob is in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons why the key fob could not function could be due to a weak connection to the buttons and internal chip or water damage.
If your key fob suddenly stopped working, or you’ve tried everything at home to solve the issue (e.g. You could have a malfunctioning 500 receiver module If you’ve tried replacing it with a battery, reprogramming it, or using an alternative key fob. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It converts the signals into electronic commands that are then translated by the vehicle.
Luckily, there is an easy method to reset all of the on-board systems in your 500, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Reconnect the battery. This will remove any remaining electricity and restart the car’s computers, which could help get your key fob working again. If the problem persists you should speak with an experienced technician. They can determine the exact cause of your problem.