Reasons Your fiat 500 new key 500 Key Fob Won’t Work
A key fob with the program fiat stilo key 500 key fob, read this post from www.valeriarp.com.tr, 500 number is a handy way to open the doors and start the car. There are a myriad of reasons the fob could stop working. It could be due to a dead battery damaged receiver module, water damage issues, or interference.
This listing is for a NEW replacement fiat 500 keys derby fiat key fobs Flip Key Remote – look-alike Ilco brand that must be programmed professionally by a local automotive locksmith (click here to search for a Locksmith Search). It comes with lock, unlock and trunk buttons.
Dead Coin Battery
The most frequent reason that your 500 key fob doesn’t work is an inactive battery. Modern key fobs have a limited operating range, and must be within just a few feet of the vehicle to function. If you are far from your vehicle when you press the key fob button, the car won’t respond and will display an “Key Fob Not Detected” message in the instrument cluster.
If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a fresh one of a reputable brand such as Panasonic Duracell or Energizer. You can find them in your local hardware store or online.
After you’ve replaced the coin cell battery It is possible to test it by standing close to your fiat punto remote key replacement 500 and pressing the buttons. The parking lights should light up and the key fob should operate the lock and unlock switch.
If the key fob won’t function after replacing the battery, it may be damaged by water that blocks it from communicating with the receiver module in your car. Water damage can occur in many ways, including a simple splash or submerging the key fob in saltwater at the beach. If you suspect that your fob has been exposed to water, place it in a bag of rice to draw out the moisture. If this isn’t working, you’ll have to get your fob replaced by an auto locksmith or a dealer.
Water Damage
Although the fob is equipped with rubber seals to keep water out of the electronic chip inside the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater is particularly dangerous to the fob’s circuit board that can cause it to short out and eventually die. If you get the fob wet, it’s not an option however, if you drop it into a cup of water or forget to take it out of your pants pocket before running the washer, don’t give up hope.
First, remove the battery from the fob. Clean the electronic chip with isopropyl alcohol or another similar product and then dry it completely before replacing the battery. Test the fob next to verify if it’s functioning. If the key does not function, it may have to be reset. This is usually handled by an auto locksmith or dealer.
If your key is old and is not programmed for your vehicle You will need to replace it completely. This is a simple procedure that can be handled by a professional locksmith for automotive use. The locksmith must cut the key to match the ignition in your vehicle. They’ll also need to reprogram the fob for the system of your car. This is an affordable and quick process that could be completed within the same day.
Receiver Module Issues
One of the most common reasons why your 500 key fob might stop functioning is because it’s out of range. The remote typically has 30 feet of range or less, and if it’s too far from your vehicle, it will not respond to your commands. It’s easy to fix this by moving the remote closer to your car until it responds.
If you’ve replaced your coin battery (commonly called a “button” or “watch”) and the fob isn’t working it could be due to an internal circuit board issue. Reprogramming the fob is usually the solution to this issue. You can find the procedure for the majority of vehicles on YouTube or in the owner’s manual.
It could be necessary to replace the metal clips that hold the coin batteries in their place. If they lose tension, it could prevent your coin battery from sitting properly and cause your remote to malfunction.
In rare cases, the fob may become desync’d with your vehicle due to software or hardware issues. It is possible to fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In some instances, they may need to reinstall the software in your body control module, as well.
Interference
Interference can also cause the key fob to not receive or transmit signals. This could happen if the key fob is located near the radio transmitter (cell phones and radar detectors) or any other source of electromagnetic radiation. The key fob might not function because of a weak connection to the buttons, water damage or damage to the internal chips.
If your key fob suddenly stopped working, or you have tried everything at home to resolve it (e.g. replacing batteries, reprogramming or using the spare key fob, you could have a defective receiver module on your 500. The receiver module, which is located beneath the dashboard, detects radio frequency signals from your key fob. It transforms the signals into electronic commands that are then interpreted by the vehicle.
There is a straightforward method to reset the 500’s in-board system, including the keyfob. Disconnect the battery 12 volt for about 15 minutes by disconnecting the negative cable first then the positive cable. Then, reconnect the battery. This will remove any remaining electricity and restart the car’s computers, which could allow you to the key fob to function again. If the issue persists, you should consult an expert technician. They will be able to identify the root cause of your issue.