Reasons Your fiat ducato key fob 500 Key Fob Won’t Work
A key fob from fiat 500x key 500 allows you to easily open doors and start your vehicle. There are many reasons why the key fob might stop working. This includes a dead coin-battery, water damage, issues with the receiver module, and interference.
This listing is for an NEW replacement fiat key fob replacement Remote key replacement (http://www.annunciogratis.net/author/trucknation51) Flip Key Remote – similar to the Ilco brand that must be professionally programmed by a local locksmith (click here for Locksmith Search). Includes lock, unlock and trunk buttons.
Dead Coin Battery
The most common reason your 500 key fob doesn’t function is due to the battery is dead. Modern key fobs have a limited range of operation, and must be within just a few feet of the vehicle to operate. If you’re far from your vehicle, and you press the key fob button the car won’t respond, and will display a “Key Fob Not Detected” message in the instrument cluster.
If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a brand new key for fiat 500 one of a trusted brand such as Panasonic Duracell or Energizer. They are available at your local hardware store, or online.
After you’ve replaced the battery of your coin cell you can test it by standing in front of your fiat 500 flip key repair 500 and pressing the buttons. The car will blink its parking lights, and the key fob will operate the lock and unlock switches.
If the key fob doesn’t function after replacing the battery, it could be damaged by water, which prevents it from communicating with the receiver module in your vehicle. Water damage can occur in many ways, including the simple splash or submerging the key fob into saltwater at the beach. If you suspect your fob was exposed to water, try placing it in a dry rice bag to draw the moisture back out. If that doesn’t work, the fob might need to be reset by an experienced auto locksmith or the dealer.
Water Damage
While the fob has some rubber seals that keep water out of the electronic chip inside it, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater is especially dangerous to the fob’s circuit board, causing it to short out and eventually end up dying. The fob getting wet is not an ideal idea however, if you drop it into an empty cup of water, or fail to remove it from your pants pocket prior to running the washer Don’t give up hope.
First, remove the battery from the fob. Before replacing the battery, clean the electronic chip with isopropyl or another similar product. Test the fob next to determine if it’s working. If the key does not work, it might need to be changed. This is typically done by a professional or dealer auto locksmith.
If the key you have is older and is not programmed for your car You will need to replace it completely. A professional automotive locksmith can complete this simple process. The locksmith will need the key cut to match your car’s ignition. They’ll also have to reprogram the fob to your vehicle’s system. This is an affordable and quick procedure that can be completed in the same day.
Receiver Module Issues
The 500 key fob could stop working because it is out of range. The remote usually has an operating range of 30 feet or less and if it’s far from your vehicle, it will not respond to your commands. It is possible to solve this problem by moving the remote closer to your vehicle until it responds.
If you’ve replaced the coin battery (commonly known as”button” or “button” or “watch”) and the fob isn’t working, it could have an internal circuit board issue. In most cases, reprogramming the fob will solve the issue. You can find the steps for most vehicles on YouTube or in the owner’s manual.
It is possible to replace the metal clips that keep the battery of your coin in place. If they lose tension it could hinder the coin battery from being properly seated, and this will cause your remote to malfunction.
In rare cases the fob might become disconnected from your vehicle due to software issues or hardware issues. This could be a huge problem, but you can frequently fix this issue by visiting an auto locksmith to have them reprogram your fob for you. In some cases, they may need to reinstall the software in your body control module, too.
Interference
In addition to a dead battery on a coin The key fob might not be receiving or transmitting an signal due to interference. This could occur if the keyfob is in close proximity to a radio transmitter, like a cell phone or radar detector. The key fob could not work due to a poor connection to the buttons water damage or damage to the internal chips.
If the key fob stopped working one day out of the blue or even after trying everything you can at home to solve it e.g. battery replacement, reprogramming and using the spare key fob, you may have a malfunctioning receiver module on your 500. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.
Luckily, there is an easy method to reset every single system on board in your 500, including the key fob. Disconnect the battery 12 volt for about 15 minutes, by removing the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electricity and restart the car’s computers. This could allow you to the key fob to function again. If the problem persists you should seek out an expert technician. They can identify the exact cause of problems.