How to Replace the Replacement Key Battery For the Saab 9-3
saab 9 3 key replacement owners have a unique set of steps to add a second key. It requires dealer support using an electronic handheld computer called Tech-2. Then the transponder must be replaced and a key have to be purchased.
Rotate your keys to prevent one from wearing out quicker than the next. This will also help keep your keys in pristine condition.
Replacement Case
In contrast to the traditional Saab keys of the past keys, the new key fobs contain electronics which makes it hard to make a copy. This has made car theft much more difficult than twenty years ago. It has also made it more costly to replace keys that were lost.
Every owner of a saab key 9-3 needs to have at minimum two working keys. It’s expensive to replace a lost or damaged key since it requires replacing the CIM module, and reconfiguring the locking cylinders. Dealers charge between $100-$200 for this.
There are a few ways to avoid the high price. Certain parts suppliers will utilize the code of a spare key to cut a new metal blade at a fraction that of a dealer. The key must be exactly the same as the original to allow it to work in your vehicle.
You can also replace the case yourself by following these steps. You’ll require a flathead screwdriver as well as some patience. With the screwdriver slowly tear the plastic away and then separate the emergency key from the case. Once you have the case open, take the electronics out and place them into your new case. Make sure you insert the correct key and badge back in the case too.
Replacement Battery
The saab car keys 9-3 key replacement (visit the next document) 9-3 replacement battery is a low-cost part that can be quickly and easily replaced. Cyclone’s YouTube video Cyd demonstrates the procedure for replacing the remote fob battery with just four easy steps. This tutorial should work for any modern saab key fob although the process might differ slightly.
The first step is to find the button that lets off the backup key in the fob. It’s usually just below the Saab logo on the back of the fob. Next you will need a flathead screwdriver into the tiny hole in this button. This should be enough to open the fob’s case to allow you to replace the battery.
Once you have installed the batteries CR1632, it is possible to reassemble the remote key fob. You can then program it into your car. The entire process should not take more than an hour at most. It is a very simple procedure that doesn’t require any special equipment.
If you lose a key the process is more complicated however, it can be done. The dealer has to first verify the VIN of the vehicle and then order an alternative TWICE module, as well as a key blade with the correct unique code. The dealer will then need to program the key using MDI, a brand new software tool.
Replacement Key Fob
The key fob is the part that locks and unlocks your car. It is equipped with a battery inside. The batteries last for a certain time, and they will eventually go out of service. This is a regular issue that happens to all cars, and the good news is that you can replace the batteries on most key fobs without replacing the whole case. Amazon sells fobs for replacement that already have all the electronics installed. It is easy to open the case and replace the batteries. It is important to note that you’ll need take out the emergency key first, and you can do this by inserting a small flathead screwdriver into the slot that is located in the middle of the case. The case should split when you rotate the screwdriver around it.
When you are ready to replace the keys, ensure that you have a spare, because this can cut down the total cost by a significant amount. If you have a spare you can ask the dealer to cut the new key and program it to the car, which is cheaper than replacing the entire key fob.
It is possible to add another key to your car If you don’t already have one, but it takes some research and effort. The cost for adding a second key is around a hundred dollars and it also requires the programming of the car’s computer. Professionals can do this however it’s a costly option.
Replacement Ignition
Unlike earlier Saab vehicles, the latest SAAB 9-3 models have an extremely sophisticated alarm system that is built on a key code. This means that should you lose only one working key, adding an additional one could be extremely costly since the car needs to have a computer module added and it also needs to be specifically programmed to accept an extra key. Most locksmiths can’t do this and even a dealer will charge several hundred dollars just to program the new key!
If you’ve lost your only working key and a dealer is able to replace the computer in your car (known as the CIM or saab key replacement near me TWICE) to create an exchange, and they will charge top dollar for it. Instead we can reprogram the EEPROM in your current car computer to allow it to be programmed for a replacement key, saving you over 50% of what you’d pay at a dealership.
If you’ve been a long time owner of a 03-11 SAAB 9-3, you probably are aware that the ignition key isn’t very durable. They can become incredibly sticky, and the buttons are known to be ripped off every now and then It is recommended that you consider replacing your ignition key if it isn’t performing as it should. It’s not as difficult as you think to replace the ignition key. With the right tools, it is able to be accomplished in a short time.