What to Do If Your Key Won’t Turn in the Ignition
If your key becomes stuck in the ignition or if it doesn’t start the car, you may require replacing the ignition and key replacement switch or key cylinder. This is a complicated job that requires special equipment.
Connect the battery after you have installed the new switch and test it. Turn the key to On.
Identifying the problem
A key that will not turn in the ignition is not only an annoyance, but it could also hinder you from getting your Car ignition system repair started. If you’re in this position there are a few actions you can take to resolve the issue prior to calling an emergency car ignition barrel replacement near me repair service.
The first step is to make sure that the key has not being inserted incorrectly. It may seem odd that the key that fits in the lock on one side will not turn when inserted in the other, but it is frequent for drivers to insert their key into the incorrect cylinder. This is why having a spare or emergency key is such an excellent idea. It will help you avoid this type of situation and get back on the road as quickly as possible.
Check the ignition and key for any debris or dirt that could cause a problem. Abrasive turning can cause the pins within the cylinder of the ignition lock to be misaligned, which is why it’s important to be gentle when trying to start the engine.
If wriggling the key does not work, try using a small tack hammer to tap it gently to loosen the springs and pins in the ignition cylinder. This technique works as tapping the cylinder creates vibrations that encourage springs to move. This in turn allows the key to be turned. Be aware that should you use too much force you could break the ignition cylinder and the key.
Another option is to try by lubricating the cylinder as well as the key by using a penetrating oil. This can be helpful in the event that the key becomes stuck because of a buildup of grime, as it will loosen and move around freely once the mechanism is lubricated.
If none of these solutions work, it is probably time to call for an emergency auto repair service. The locks and cylinders of these vehicles get worn out over time and are especially damaged if they’re frequented and a key that isn’t turning can be a sign that it is time to replace it.
Prepare for the Replacement
Many people believe that the first thing they do when their car has problems is to call the dealer. While many dealers offer service for cars, not many people are aware that they can also fix their issues at an affordable cost through an independent garage or locksmith. If your key isn’t going into the ignition, it could be an indication that your ignition cylinder is starting to fail and it’s time to replace it.
There are a few things you’ll need to get done prior to starting the replacement process. First, you’ll need to locate a safe place to work. You must be away from the road and the parking brake should be engaged. You’ll also have to disconnect the negative battery cable to stop the activation of electrical systems while you’re working.
The next step is to remove any steering columns or dashboard covers that prevent easy access to the ignition. This will enable you operate more efficiently and lessen the chance of damaging the components of your vehicle. It is also important to make certain that you have all the necessary tools available before beginning. The more precise the tools that you have, the easier it will be to complete the job correctly.
Once you have the tools that you require, it’s the time to start preparing for the replacement of the ignition cylinder. You’ll need to look over the cylinder’s ignition and determine whether it can be fixed simply by replacing or smoothing the wafers inside. If the cylinder’s ignition cannot be repaired, you will need to replace it by locksmiths.
If the cylinder that controls the ignition is in good working order you may try to fix the issue with a chisel or flathead screwdriver to push into the keyway and then rotate it to release it. Be careful not to apply excessive force as this can cause more damage than it repair. If this method doesn’t work then it might be necessary to drive your tool further into the cylinder to create more torque and leverage.
Take off the Ignition Cylinder
The ignition lock cylinder is the place where your key goes into the vehicle to enable it to start its engines and turn on other systems like your radio. It is located within the ignition switch. This electronic component locks the ignition, and reads the anti-theft code inside your key.
The lock cylinder is made up of pins that move up and down to allow the mechanical key to enter and turn. Over time the pins wear out (and even break) or become stuck. This blocks the key from turning and activating the vehicle. If you don’t fix the issue, your vehicle may not start or be locked.
Fortunately the ignition cylinder can be repairable by an alternative one to help restore your vehicle’s ability to start. To do so, first disconnect the battery. The steering wheel trim needs to be removed in order to access the ignition switch. It’s important to keep in mind that the procedure varies from one model to the next and so consult your repair manual for directions.
After the old cylinder has been removed, you’ll need buy a new one that matches the key in your car and then follow the instructions in the repair manual to put it in. Before you finish, it’s a good idea check the new key to ensure the proper operation.
The first indication of a defective ignition lock repair services cylinder is having trouble getting your car started. The key may be hard to insert and turn, requiring that it be jiggled or fiddled with to get it to move. It might be difficult to remove the key. This can be an indication that it has become bent or worn out and is in need to replaced.
It is convenient to have a Wrench mobile technician come to your office or home to provide a quick and reliable ignition lock cylinder auto repair. This way, you don’t need to transport your vehicle to a repair shop. We can help you get your vehicle back on the road in no time with professional repairs and a simple estimate.
Installing the New Switch
The ignition switch is an essential component in your car, and one that can malfunction in time. This can cause a range of issues, such as your car not starting, or the check engine light going on. It is essential to replace your ignition switch if you suspect that it is failing.
Depending on your vehicle’s model and make it is possible to remove panels or covers in order to get access to the ignition. If you must remove covers or panels then disconnect the electrical connectors and remove any bolts that hold the switch in place. Install the new switch after you have removed the old one. Once the switch is installed connect the wire and test it.
Make sure that the switch is in the OFF position prior to installing the new one. You may need to reset the system if you are replacing the lock cylinder and the switch. Based on the vehicle you drive the procedure can be complex and require special tools.
When you’re done, reinstall the panels or covers you removed and connect the battery. Make sure you have the right replacement ignition switch for your vehicle. Enter your year, model, and model into the AutoZone search box to locate the correct switch. The site will provide you with the list of ignition switches that work with your car and have the right part number.
Whether you use a traditional key or a push button start system, your ignition switch is vital to keep your vehicle running. However, it’s a delicate and delicately built part that can get worn out in time due to regular use or environmental factors. When inserted, heavy keys can put strain on the switch. Extreme temperature changes can also impact the lubricants and materials. If your switch is damaged it is essential to have it replaced immediately to ensure the safety of your vehicle as well as its passengers.
If you are replacing your ignition switch, it is recommended to hire an expert handle the task for you. This will ensure that the new switch is compatible, and all connections are secure. It will also help you avoid costly mistakes that could damage your vehicle or cause issues due to the new ignition switch.